The Push for U.S.-Made Drones: What It Means for Carbon Fiber Airframe Sourcing

 

Since mid-2025, federal policy has moved hard toward drones built in the United States. An executive order, a Pentagon directive, and FCC action have all pushed buyers toward domestic systems and domestic components. Most of the attention has gone to electronics such as flight controllers, radios, cameras, and batteries. But a drone is also a structure, and in many designs that structure is carbon fiber. This post covers what’s changed and what drone developers should consider when sourcing composite airframe parts.

Sourcing carbon fiber structures for a U.S. drone program?

CMI is a U.S.-based, ITAR-registered composite manufacturer with in-house engineering and tooling.

Talk With Our Team

What Changed in Federal Drone Policy

The June 2025 executive order

Executive Order 14307, “Unleashing American Drone Dominance,” was signed on June 6, 2025. It states that building a strong and secure domestic drone sector is vital to reducing reliance on foreign sources, and it sets a policy of “strengthening the domestic drone industrial base.” It directs agencies to prioritize drones manufactured in the United States over those made abroad, and directs the Secretary of Defense to prioritize procurement of drones that comply with section 848 of the FY 2020 NDAA and are made by U.S. companies (The White House).

The July 2025 Pentagon memo

On July 10, 2025, the Secretary of Defense issued the memo “Unleashing U.S. Military Drone Dominance.” According to DefenseScoop’s reporting on the memo, it states that major purchases “shall favor U.S. companies,” calls for each service to stand up program offices focused on unmanned aircraft systems, and sets a goal of equipping every squad with low-cost, expendable drones by the end of 2026 (DefenseScoop).

The FCC Covered List

In December 2025, the FCC added uncrewed aircraft systems and UAS critical components “produced in a foreign country” to its Covered List, which bars covered equipment from receiving new FCC equipment authorizations. The named critical components include flight controllers, communications systems, navigation systems, sensors and cameras, batteries, and motors, and the list is described as “not limited to” those items (FCC DA 25-1086). The FCC later set out exemptions for items on the Defense Contract Management Agency’s Blue UAS Cleared List and for items that qualify as “domestic end products” under the Buy American standard in 48 CFR 25.101(a) (FCC DA 26-758). The details and deadlines of these exemptions have continued to change during 2026, so developers should check the FCC’s current notices and get their own regulatory advice.

Where Carbon Fiber Fits

None of these documents name the airframe as a critical component. But the airframe still matters to a domestic sourcing strategy, for two practical reasons.

First, carbon fiber is a common structural material in drones. A 2025 review of drone materials notes that “carbon and Kevlar fibers dominate UAV applications due to their high stiffness-to-weight ratio,” and that high-stiffness, low-weight materials have become increasingly critical for improving flight endurance (Vedrtnam et al., Journal of Composites Science). That makes the airframe one of the larger structural purchases on many platforms.

Second, the domestic end product test under the Buy American standard looks at the cost of a product’s components, not only its electronics (FAR 25.101). Where the frame, arms, and housings are made can therefore affect a program’s domestic content calculation. Developers should confirm how this applies to their own product with qualified counsel.

What to Ask a Composite Airframe Supplier

If you are moving airframe production to a U.S. supplier, these questions help separate a capable partner from a reseller:

  • Where are the parts actually molded, trimmed, and assembled?
  • Who owns and builds the tooling, and where is it kept?
  • Can the supplier scale from prototypes to production tooling without a new vendor?
  • How are materials traced from lot to finished part?
  • What inspection and testing are done before parts ship?
  • Is the supplier registered with the State Department’s Directorate of Defense Trade Controls (DDTC) if the program involves defense articles?
  • Can the supplier machine metal hardware and install inserts, or will that go to another shop?

How CMI Supports Domestic Composite Programs

Split Drone Blueprint and Physical Design

CMI’s engineering, tooling, composite manufacturing, and assembly are all located in San Clemente, California. CMI is registered with DDTC under ITAR, designs and builds its molds in-house, and can move from prototypes to hard tooling capable of producing thousands of parts. Production processes include prepreg layup with autoclave or out-of-autoclave cure, resin transfer molding, vacuum infusion, compression molding, and 3-, 4-, and 5-axis CNC trimming. CMI also machines metals and can co-mold metal inserts into composite parts.

To learn more about what DDTC registration means for a manufacturer, see the ITAR registration rule at 22 CFR 122.1. To see how CMI runs production, visit our manufacturing and assembly page.

Bring your airframe drawings to a U.S. composite manufacturer.

CMI can review your design for manufacturability, tooling, and production volume.

Contact CMI

Share:

More Posts

Let’s Collaborate on Your Next Project